Christmas Stable

Project:
It all started with an innocent email from my pastor's wife asking if I could build some sort of stable for the Christmas production. After thinking about it for a little while and meeting with her to find out the extent of what she was looking for I agreed.

Process:
The first step was to try to find an old barn from which I could scour some materials. I wanted to make it look old and weathered as opposed to building it with new lumber. I remember from when I used to live out in Memramcook that there were several barns that had fallen down over time and on one of my trips out there I found one that I thought could work.

After knocking on 3 different houses, I finally found someone who knew who actually owned the property and he said he'd find out whether I could use some of the wood. The next week I had to go back out to Memramcook so I stopped by his place and he said that I was allowed to take as much as I needed.

The next day I loaded up the van with some demolition tools as well as Nathaniel to go for a little "Bid and Destroy" adventure.

I envisioned the entire stable to be constructed in sections that were small enough to carry and assemble by one person as follows:

Left wall: 3'-6" wide by 5' high
Right wall: 3'-6" wide by 5' high
Back wall bottom: 9' wide by 2'-6" high
Back wall middle: 9' wide by 2'-6" high
Back wall top: 9' wide by 2' high (triangular)
Front support beam: 9'-8" wide by 2' high (6x6 lumber)
Left roof: 4' wide by 5'-6" long
Right roof: 4' wide by 5'-6" long
Hay storage part one: 3' high by 3'-6" wide
Hay storage part two: 3' high by 2' wide

All of these are held together by 37 lag bolts. I designed it in a way that nothing should be confusing and none of the lag bolts could get lost so after everything was taken apart into its sections I drilled 37 holes in the back of the main support beam to store the lag bolts for future use.

Pictures:

The barn in all its glory

View from the inside

Nathaniel scouting out the "woods"

Measuring and cutting up the required lumber with the chain saw

Miss Ellie and Mel came for a visit

Van full of boards and beams

View after I had cut out a bunch of lumber

Back home in my shop after the second load of lumber was just "harvested"

Building the walls first, all in sections that one person could carry and assemble

The cut-out for placing the main roof support beam onto the wall and post

Building the top module of the back wall

One roof section

It's coming together nicely

I had to remove all the cedar shakes from the wobbly section I had cut out of the barn to re-staple them on a new base for the roof

I ended up welding a piece of metal bar to my air powered mini jack hammer to pry the shingles off the old roof

This is about a quarter of all the shingles needed for both roof sections

Starting the build-up of the roof sections, one shingle at a time

Finished roof section

Almost done

After I built a little area for putting hay bales

Some of the larger left-over pieces that I drove back out to the old barn

Lag bolt storage

Lag bolt storage

The bottom two rear wall sections

Rear wall, side wall and roof sections

After it was set up at the church

Another Angle

During the production

Another angle with the wise men

A nice close-up shot

Tools:

Chain saw, hammer, crow bars, 5' breaker bar, vise, chain saw sharpener, measuring tape, pencil, marker, table saw, mini-jack hammer, air stapler, air compressor, planer, jig saw, reciprocating saw, framing nailer, cordless drill, 1/2" and 5/8" socket and ratchet, chop saw, ladders, drill bits

Materials:
Old wood from barn, 37 lag bolts, sun bleached wood stain to fix minor imperfections, nails

Cost:
$110.55

Time:
30hr

Savings:
$1,400.00

Conclusion:
Looks good, but then again, that's just my opinion